 |
|
|
|
| Agfa CP-1000 Table Top Film Processor. |
 | FILM PROCESSOR - CP1000 The CP-1000 provides consistent, high-quality processing of film sizes ranging from 4" x 4" up to 14"W x 36"L for applications with moderate patient film volume. Fast Processing 125-second cycle time (leading edge into developer to leading edge at dryer) for quick access to finished radiographs. Energy Efficient The CP-1000 operates on only 400 watts of power. Economical stand-by mode reduces power to 100 watts when processor is idle. To further reduce power consumption, the processor may be turned off when not in active use, and quickly restarted because of its fast warm-up time. Advantages Over Typical Low-Volume Processors The typical processing cycle for low-volume processors is 2.5 to 3 minutes, and you must remain in the darkroom until the film has completely entered the processor, which can take over a minute. The exclusive CP-1000 Feed Tray/Light Cover allows you to leave the darkroom in about 15 seconds. |
| Most processors require water, drain plumbing and external replenishment. They consume 16 to 30 gallons of water per
hour. The CP-1000 requires no external plumbing, and the wash-water is supplied from its 5-liter (1.3 gallon)
dispenser bottle. Only .25 gallon of chemical is required to fill the CP-1000 Processor tanks, and they are replenished automatically. Where other processors typically require 5-gallon mixers to keep their tanks full, the CP-1000 uses premeasured concentrates that make the right amount of developer and fixer to fill the 5-liter dispenser bottles. With the CP-1000 you mix and use less chemistry and it is always fresh. About 60 mixed sizes of film can be processed with 5 liters of developer. Average processing cost is about 40 cents per film. The CP-1000 uses a simple, accessible film transport system with fewer rollers instead of conventional heavy roller racks. Clean-up is much easier. The CP-1000 uses an infrared dryer instead of the typical hot-air dryer. Fast drying, quiet and energy efficient. The CP-1000 uses only 400 watts of power compared with the typical 1500 watts for other processors. Uses only 100 watts in standby mode. |  |
 | Short start-up time for the CP-1000 allows it to be shut off when it is not being used, and restarted when needed. It
can be ready for processing from a cold start in only seven minutes. Easy set-up - Simply unpack and plug into any standard power outlet. Insert filled chemical and wash-water bottles, and you're ready to process films. No plumbing is needed. Fast start-up time - Operational in seven minutes from a cold start...can be turned off when not in use. No mixers or measuring - Convenient premeasured concentrate provides fresh, consistent and precise amount of chemistry for dispenser bottles. Chemical mixer is not needed. 5-Liter replenishment supply - Less frequent refilling of dispenser bottles. Automatic replenishment - Internal scanner monitors film throughput...ensures potency of chemistry. Tanks drain into portable waste containers. Infrared dryer - Rapid film drying, energy efficient, quiet operation, and no venting is required. Feed tray/light cover - Gets you out of the darkroom faster. EASY TO SET UP |
| Does not require professional installation and plumbing. Setting up and installing the CP-1000 takes less than one
hour and requires only simple tools. EASY TO PROCESS FILM Open the Feed Tray/Light Cover, feed film into processor, close Light Cover as soon as film is clear. You may now leave darkroom without fogging film. Film is deposited into receiver tray, ready for viewing in about two minutes. EASY TO CLEAN With the cover removed, the tanks are easily drained. Rollers, guide plates and chemical tanks lift out and are easily rinsed in a convenient sink. The processor can be properly cleaned in only minutes. EASY TO OPERATE There are only three controls... Power On/Off Switch - Turns processor and tank heaters on. Manual Replenishment Feed Light - Used to manually start replenishment cycle when processor has been idle for more than a day. The Film Feed Light is illuminated during the replenishment cycle and when film is passing through the processor. When the light turns OFF, a new film may be fed into the processor. Dryer Temperature Step-Switch - Adjusts temperature of infrared dryer if required. |  |
 | SIMPLE FILM PATH When film enters the processor, it passes the film scanner which regulates the replenishment system. A series of rollers transport the film through the developer, fixer and wash-water tanks and the dryer section. The film exits the dryer and is deposited into the receiver tray. EASY CHEMICAL MIXING 1. Fill developer and fixer dispenser bottles to 2.5 L mark with clean water. 2. Pierce seals of two bottles of Agfa developer concentrate, Part "A", and pour into dispenser bottle. Agitate slowly to mix solution. 3. Perform the same step with concentrate Part "B", and fill dispenser bottle to the "FULL" mark with water. Replace valve and shake thoroughly to mix solution. 4. Follow similar procedure as in steps 2 and 3 for mixing Agfa fixer concentrate. 5. Fill Wash-Water Bottle with clean water to "FULL" mark and replace valve. 6. Insert each bottle into the processor. That's all there is to mixing chemicals for the CP-1000 Processor! |
 |
 |
|
